Samsung SilverCare TM Washer Owner's Manual

Samsung SilverCare TM

Washer Owner's Manual

j i'!v_: _ "7

ii _ ......i

i i s

........................ i i,/

....................._J

www.sams ung.com/global/register

Code No.: DC68-02291A-08_EN

1.SilverCareTM Sanitization

The winning combination! Samsung's silver nano technology combines the sanitizing effect of silver

with state-of-the-art science for the ultimate in clean. Two plates of 99.9% pure silver are converted

into silver ions through electrolysis. Even in cold, bleach-less water, the silver particles remove 99.9% of

odorcausing bacteria for a'super clean"wash. So washing in cold water is energy efficient and better for

your clothes.

2. Extra LargeCapacity

Even bulky garments and blankets get super clean.The large 3.79 cu.ft, capacity leaves enough room for

a more thorough, cleaner wash.

3. High Efficiency Energy & Water Saving

Washing with Samsung's SilverCare TM, even in cold water, sanitizes the laundry thereby saves 92% energy

used when compared to that with hot water sanitization.

4. Direct Drive Inverter Motor

The power to handle anything! Our direct-drive inverter motor delivers power right to the washer tub

from a variable speed, reversible motor.

A beltless direct-drive motor generates a higher spin speed of 1,200rpms for more effective, quiet

operation.The washer also has fewer moving parts, meaning fewer repairs.

5.Woolmark Certified

The machine wash wool cycle on the Samsung SilverCare TM machines has been tested and passed the

required Woolmark Company specification for machine washable wool products. Fabrics should be

washed according to the instructions on the garment label as specified by Woolmark and Samsung.

Pedestal with Storage Drawers An optional 15"pedestal is available to raise the washer for easier loading

and unloading. It also offers a built-in storage drawer that can hold a 100 oz.

bottle of detergent.

6. Stacking

Washer and dryer can be stacked to maximize usable space.

Safety Precautions

Congratulations on your new Samsung SilverCareT_Washer.This manual contains important information

on the installation, use, and care of your appliance. Please take time to read this manual to take full

advantage of your Washer's many benefits and features.

What you need to know about Safety Instructions

Warningsand Important Safety Instructions in this manual do not cover allpossibleconditions and situationsthat may occur.

It isyour responsibility to usecommon sense,caution, and carewhen installing, maintaining, and operating your Washer.

IMPORTANT SAFETYSYMBOLS,WORDS, LABELS

WARNING - Hazards or unsafe practices that COULD result in severe personal injury or death.

CAUTION - Hazardsor unsafe practicesthat COULD result in minor personal injury or property damage.

WARNING - To reduce the risk of fire, explosion, electric shock, or personal injury when

using your Washer, follow the basic safety precautions below:

1. Read all instructions before using the appliance.

2. As with any equipment using electricity and moving parts, potential hazards exist.To safely

operate this appliance, become familiar with itsoperation and exercise care when using it.

3. Install and store your Washer away from weather exposure.

4. Install and level your Washer on a floor that can support its weight.

5. Your Washer must be properly grounded. Never plug it into an ungrounded outlet. See page A2 for details.

6. To avoid the possibility of fire or explosion:

• Do notwash items that have beenwashed,soaked,or treated with gasoline,dry cleaning solvents,orotber

flammable or explosive substances.Theygiveoff vapotsthat could ignite or explode.Any materialthat hasbeen

exposed to cleaning solventorother flammable liquids orsolidsshould not be placed inyour Washeruntil all

tracesof such liquids,solids,andfumes have been removed.Offending itemsinclude acetone,denaturedalcohol,

gasoline,kerosene,certainliquid household cleanersand spot removers,turpentine, waxes,andwax removers

• Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water.

They give off vapors that could ignite or explode.

• Undercertain conditions, hydrogen gas may be produced in ahot water system that hasnot been used fortwo

weeksor more. HYDROGENGASISEXPLOSIVE.Ifthe hot water systemhas not been usedfor two weeks or more,

turn on all hot water faucetsand letthe water flow for severalminutes before using yourWasher.This will release

any hydrogen gasbuild-up. Sincethe gas isflammable, do not smoke or use open flameduring this time.

7. Unplug power cord before attempting to service your Washer.

8. Do not reach into the appliance when the tumbler ismoving.

9. Do not let children play on or in your Washer.Close supervision isa must when child ren are near the Washer.

10. Do not tamper with controls.

11. Do not repair, replace, or service any part of your Washer unless you fully understand the recommended

user-repair instructions and have the skills to carry them out.

12. Store laundry aids and other material in a cool, dry place out of children's reach.

13. Do not wash or dry items that are soiled with vegetable or cooking oil.These items may contain some oil after

laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself.

14. Do notusechlorine bleach,ammonia,or acids(suchasvinegarorrustremover)in thesamewash.Hazardousfumescanform.

15. Do not machine washfiberglass materials.Small particlescan stickto fabricswashed in following loadsand cause

skin irritation.

16. Before your Washer is removed from service or discarded, remove the door to the washing compartment to

avoid the danger of children or small animals getting trapped inside.

17. Do not siton top of your Washer.

18. Inlet hoses are subject to damage and deterioration over time. Check the hoses periodically for bulges, kinks,

cuts, wear or leaks,and replace them every five years.

19. Ensure pockets are free from small irregularly shaped hard objects, foreign material, etc. ie. coins, knives, pins,

etc.These objects could damage your washer.

20. Do not wash clothing with large buckles, buttons, or other heavy metal.

SAVETHESE INSTRUCTIONS

Table of Contents

Installing Your Washer ............................................... A-1

UNPACKINGYOUR WASHER ............................................. A-1

OVERVIEW OF YOUR WASHER ............................................ A-1

GROUNDING ....................................................... A-2

WATER ........................................................... A-2

DRAIN FACILITY ..................................................... A-3

FLOORING ......................................................... A-3

LOCATION CONSIDERATIONS ............................................ A-3

ALCOVE OR CLOSET INSTALLATION ........................................ A-3

IMPORTANTTO INSTALLER .............................................. A_4

Operating Instructions ................................................ B-1

LOADINGYOUR WASHER ................................................ B-1

GETTING STARTED .................................................... B-2

Washing a Load of Laundry ............................................ C-1

OVERVIEW OF THE CONTROL PANEL ........................................ C-1

CHILD LOCK ......................................................... C_4

GARMENT + ......................................................... C_4

MY CYCLE .......................................................... C_4

FOR SILVERCARP WASHING (select models) .................................. C-5

DETERGENT USE...................................................... C-6

FEATURES .......................................................... C-6

Maintaining Your Washer ............................................. D-1

CLEANING THE INTERIOR ............................................... D-1

CLEANING THE DISPENSERS ............................................. D-1

STORING YOUR WASHER ............................................... D-1

Troubleshooting .................................................... E-1

CHECKTHESE POINTS IFYOUR WASHER ........................................ E-1

INFORMATION CODES .................................................. E-3

Appendix ......................................................... F-1

FABRICCARE CHART ................................................... F-1

HELPING THE ENVIRONMENT ............................................. F-2

DECLARATION OF CONFORMITY .......................................... F-2

SPECIFICATION ....................................................... F-2

CYCLECHART ....................................................... F-3

/-\

UNPACKINGYOURWASHER

Unpack your Washer and inspect it for shipping damage. Make sure you have received all of the items

shown below.

If your Washer was damaged during shipping, or you do not have all of the items, contact 1-800-

SAMSUNG.

OVERVIEWOFYOURWASHER

Deterg,

Control

Hot water supply hose Cold water supply hose

[ Hose

Adjustable leg

Spanner

(use for the Upper Bolt Hole)

Bolt hole covers

Water Supply Hose Hose guide

SAMSUNG CIothesWasherOwner'slnstructions A-1

BASICLOCATION REQUIREMENTS:

ELECTRICAL

* 120Volt 60 Hz 15 AMP fuse or circuit breaker

* Individual branch circuit serving onlyyour Washer is recommended.

* Your Washer is equipped with a power cord.

NEVER USE AN EXTENSION CORD.

GROUNDING

ELECTRICAL GROUNDING [S REQWREDON THIS APPL[ANCEo

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a power cord having a three-prong grounding plug for use in a properly

installed and grounded outlet.

_hllL WARNING - Improper connection of the equipment-grounding conductor can result in a

risk of electrical shock. Check with a qualified electrician or serviceman if you

are in doubt as to whether the appliance is properly grounded. Do not modify

the plug provided with the appliance - if it does not fit the outlet, have a proper

outlet installed by a qualified electrician.

IMPORTANT SAFETY PRECAUTIONS

* To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and grounding

must be done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest Revision

and local codes and ordinances. It is the personal responsibility of the appliance owner to provide

adequate electrical service for this appliance.

NEVER CONNECT GROUND WIRETO PLASTIC PLUMg[NG LINES,GAS LINES,OR

NOT WATERP[PESo

WATER

To correctly fill your Washer in the proper amount of time, water pressure of 20 - 120 psi isrequired.

Water pressure less than 20 psi may cause water valve failure, not allowing the water valve to shut off

completely. Or it may extend the fill time beyond what your Washer controls allow, resulting in your

Washer turning off. A time limit isbuilt into the controls in the event of an internal hose becoming loose

and flooding your home.

The water faucets must be within 4 feet/122cm of the back of your Washer for the inlet hoses provided

with your Washer.

NOTE: Accessory inlet hoses are available in various lengths up to 10 feet/305cm for faucets that are

further away from the back of your Washer.

To avoid f:he po_b_l#y of w_t_r damage:

* Havewater faucets easily accessible

* Turn offfaucets when Washer is not in use.

* Periodically check there is no leakage at water inlet hose fittings.

_[d_[l_ WARNING - CHECK ALL CONNECTIONS ATTHE WATER VALVE AND FAUCET FOR LEAKS.

A-2 SAMSUNG CIothesWasherOwner'slnstructions

DRAIN FACiLiTY

The recommended height of the standpipe is 18 in/46 cm.The drain hose must be routed through the

drain hose clip to the standpipe. Standpipe must be large enough to accept the outside diameter of the

drain hose.The drain hose isattached at the factory.

FLOORING

For best performance, your Washer must be installed on a solidly constructed floor. Wood floors may

need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile

surfaces are contributing factors in vibration and/or tendency for your Washer to move slightly during

the spin cycle.

Never install your Washer on a platform or weakly supported structure.

LOCATIONCONSiDERATiONS

Do not install your Washer in areas where water may freeze, since your Washer wiil always maintain

some water in its water valve, pump, and hose areas.This can cause damage to belts, pump, hoses and

other components. Operating temperature should be above 60°F/16°C.

ALCOVEORCLOSETINSTALLATION

M[N[ML_M CLEARANCES FORCLOSETAND ALCOVE INSTALLATIONS:

Sides - I in / 25 mm Rear - 2.375 in / 60 mm

Top - 17 in/432 mm Closet Front - 2 in / 51 mm

If both Washer and Dryer are installed together, the closet front must have at least 72 in2or 465 cm 2of an

unobstructed air opening.Your Washer alone does not require a specific air opening.

SAMSUNG CIothesWasherOwner'slnstructions A-3

[nsta[Hng Your Washer

llVlPORTANTTOiNSTALLER

Please read the following instructions carefully before installing your Washer.

These instructions should be retained for future reference

STEP1

Removing the Shipping Bo_ts

Before using your Washer, you must remove the four shipping

bolts from the back of the unit.

1. Loosen all bolts with the supplied spanner.

2. Slide the bolt and spacer up and remove the bolt with

spacer through the hole in the rear wall of your Washer.

Repeat for each bolt.

3. Fill the holes with the supplied plastic covers.

4. Keep the shipping bolts and spacers for future use.

STEP2

Before you #_s_:aHyour Wa.sher, make sure the _oca_or_:

• Hasa hard, level surface

• Is away fromdirect sunlight

• Has adequate ventilation

• Will not be freezing (below 32°F or O°C)

• Is away from heat sources such as oil or gas

• Has enough space so that your Washer need not stand on its power cord

• Doesn't have any carpeting that will obstruct ventilation openings.

STEP 3

1. Place the drain hose in the drain facility. Be sure an airtight

connection isNOT made between the drain hose and the

standpipe.

Standpipe must be at least 18 in or 46 cm high.

NOTE: Caution must always be exercised to avoid collapsing

or damaging the drain hose. For best results, the drain

hose should not be restricted in any way - by elbows,

couplings, or excessive lengths. For situations where the

drain hose cannot be conveniently elevated to at least 18

in or 46 cm, the drain hose must be supported.

2. Check the inlet hose to ensure a washer is inside each fill hose.

Thread the inlet hoses to the HOT and COLD faucet connections.

On the other end of the hose, check for one rubber washer per

hose and install each fill hose to the water valve. Make sure the

hose with the red line isattached to the HOT faucet._ghten by

hand until snug, then two-thirds of a turn with pliers.

NOTE_ For correct water use, connect both HOTand COLD

water valves. If one is not connected,'nF"(no fill) error

can occur.

LAUNDRYTUB

_ STANDPIPE

18'rMIN _"_T[E

TRAP _'r_X

A-4 SAMSUNG CIothesWasherOwner'slnstructions

3. Turn on "HOT'and "COLD"water supply and check all connections at

the water valve and the faucet for leaks.

4. Plug power cord into a 3-Prong, well grounded 120 volt 60 Hz

approved electrical outlet protected by a I S-amp fuse or comparable

circuit breaker.

Your Washer isgrounded through the third prong of the power cord

when plugged into a three-prong grounded receptacle.

5. Slide your Washer into position.

6. Level your Washer by turning the leveling legs in or out as necessary by hand or wrench included

with your Washer.

When your Washer is level, tighten the nuts using the wrench or (-)driver.

NOTE_ Your Washer must be leveled

on all four sides. A carpenter's

level should be used on all

four corners of your Washer.

It's a good idea after the first

dozen washes to recheck your

Washer's levelness.

7. If you install your washer on softfloor,

you should place the rubber cup under

adjustable leg. Before put rubber cup,

please remove film for double-side tape

attached on rubber cup.

NOTE_ If washer is installed on riser,

you should put rubber cup

under leg for risen

SAMSUNG CIothesWasherOwner'slnstructions A-5

Operating Instructions

LOADING YOURWASHER

• You can fill the tub with dry, unfolded clothes; but DO NOT OVERLOAD the tub.

Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or

wrinkling of the load.

Wash delicate items such as bras, hosiery, and other lingerie in the Delicates/Hand Wash cycle with

similar lightweight items.

When washing big bulky items or a few smaller items that don't fill the tub completely - a rug, a

pillow, stuffed toys, or one or two sweaters, for example - add a few towels to improve tumbling

and spin performance.

When washing heavily soiled loads, not overloading your Washer is very important to assure good

cleaning results.

To add a forgotten item:

1} Press the Cycle Selector dial

2) Wait for the Door Lock light to go out (5 seconds)

3) Add the item, close the door, and press the Cycle Selector dial.

After a pause of 10 seconds, the cycle will resume.

NOTE: To ensure thorough cleaning, add items within five minutes of starting the wash cycle.

Try washing Bedding, Towels, undergarments, and other artk[es that usually have dose body

contact using the SilverCare TM Option, which Sanitizes using Cold Water.

B-1 SAMSUNG CIothesWasherOwner'slnstructions

Operatin9 Instructions

GETTING STARTED

1. Load yourWasher.

2. Close the door.

3. Add detergent and additives to the dispenser (see pages C6-C7).

4. Select the appropriate cycle and options for the load (see pages C2-C5).

5° Press the Cycle Selector dial.

6° TheWash Indicatorlight will illuminate.

7° The estimated cycle time will appear in the display.

The time may fluctuate to better indicate the time remaining in the cycle.

8. Before your Washer starts to fill, it will make a series of clicking noises to check the door lock and do

a quick drain.

NOT£$:

When the cycle is complete, the Door Lock light wi[[ go out and "End" wi[[ appear in the display.

DO NOT attempt to open the door until the Door Lock light is off.To add a forgotten item, see

"Loadin 9 your Washer" section.

When your Washer is restarted after a pause, expect a delay of up to 15 seconds before the

cycle continues.

Pressing Power cancels the cycle and stops your Washen

The Pre Wash (select models), Wash, Rinse and Spin indicator lights will illuminate during those

portions of the cycle.

SAMSUNG CIothesWasherOwner'slnstructions g-2

Washing a Load of Laundry

OVERVIEW OFTHECONTROL PANEL

Temp

Heavy Duty Towels ,_J(_)'_

Perm Press Rinse+Spin

0 Warm/Waml 0 Medium ;Heavy )Louder

............. ............. I (...... EXt,_ R,nse I Del ........

pm O.ly

)CokJ/Cold )No Sph_ C>Ught ()Off Y HandWas

Temp Spin Soil Level Signal Silver Care ::

Quick Wash

Heavy Duty .... Towe s

..........;i (_--}) ii ..........

( Warm/Warm :Medium Heavy (: Louc_et

..........1_ ' ..... ......... ........................ \XPauseij ",'L -,

..... .........::_...............................................H........\X.\_.- --//_/,,...........y

.°ps°,°So,Lo.,si.a,S,,.C°r°OW°°"%::.S;"

Quick Wash

I !!!"!I!I!I !"......................... "" !!'"..... ay Start

wa h R rise S_ !e

[ c

D _81lneb 0:llJ I) Extk_ _as h

)Hot/Cold 2Hg5 R

CbWarnl/Warm C)M_Jium ()Heavy D)Loude_

Temp Spin Soil Level Signal Silver Care

Heavy Duty ...... ,.Towels Power

Spin Only ,_ = ._

Quick Wash

L}rlay Start

Extra W_sh Extra R_,_S_

@lot/Cold 0 Iligl _.)

) waelfl/yvarn Medl irn Heavy )Louder

0 WaelTdCo[_ :) LOW :? Nomal : So:te

C Cold/Col i C f\o Spin 7; LJght C; O_f

Temp Spn Sol Level Signal

S ¸ "q / _\ /- \ © f \

_ _ i¸

C-I SAMSUNG CIothesWasherOwner'slnstructions

Washing a Load of Laundry

Displays the remaining cycle time, all cycle information, and error messages.

2. Temperaturese_ection button

Press the button repeatedly to cycle through the different water temperature options.

Extra Hot/Co[d - Heavily soiled, colorfast items. Only available with the Sanitize cycle.

Hot/Co[d -Whites and heavily soiled, colorfast items.

Warm/Warm - Colorfast items. When warm rinse is selected, only the final rinse will be warm.The

other rinses will be cold to conserve energy.

Warm/Cold - Moderately soiled, colorfast items; most wrinkle-free items.

Co[d/Co[d - Brightly colored, very Hghtly soiled items; washable woolens.

3. SD[nse[ect[onbutton

Press the button repeatedly to cycle through the different spin speed options.

Extra High - Removes more water from loads during spin.

NOTE: To minimize wrinkling of wrinkle-free and no-iron fabrics, DO NOT use the Extra High spin

option for these loads, nor overload your Washer.

High - Use for underwear, t-shirts, jeans and sturdy cottons.

Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics.

Low - Use for delicate items needing a slow spin speed.

No Spin - Drains your Washer without spinning. Use for extremely de[kate items that cannot

tolerate any spin.

4. SoN Leve_s÷[ectionhuron

Press the button to select the Soil Level/washing time.

Heavy - For heavily soiled loads.

Normal - For moderately soiled loads.This setting is best for most loads.

Light - For lightly soiled loads.

5. Signa_se_tionbutton

Press the button to increase or decrease the end of cycle signal volume or turn off the signal.

6. Si_ve_Ca_e_'_button

Press this button to sanitize your laundry in cold water.

Active silver ions are produced from pure silver plates by the process of electrolysis and released

into the wash water effectively sanitizing your wash, even in cold water, without bleach. The

SilverCare TM system sanitizes with 92% less energy use than a traditional heat sanitization.

SAMSUNG CIothesWasherOwner'slnstructions C-2

Washing a Load of Laundry

10.

Select Cycle Option

Delay Start-Any cyclecan be delayed forup to 12,19or 24 hours(selectmodels) inone-hour

increments. Displayed hour indicates the time at which the wash will be finished.

ExtraWash - Add additional time to the wash for better stain removal.

[Extra Rinse - Add an additional rinse at the end of the cycle to more thoroughly remove laundry

additives and perfumes.

Extra Spin - Add additional time to remove more water from loads

My Cycle - Choose your favorite cycle including temperature, spin, soil level, option, etc.

PreWash -To use this feature add detergent to the Pre Wash selection of the detergent

compartment. When turned on, the washer fills with cold water and detergent, tumbles, then

drains and advances to the selected wash cycle. Some cycles cannot be selected with this option/

_ ou cannot select PreWash option in the Delicate/Hand Wash, Wool, Quick Wash and Active

Wear cycles.

Cycle Se_ecto_

Select the appropriate cycle for the type of load.

This will determine the tumble pattern and spin speed for the cycle.

NOTE: To minimize wrinkling of laundry, select the Perm Press cycle.

Heavy Duty - For sturdy, colorfast fabrics and heavily soiled garments.

Normal - For most fabrics including cottons, linens, and normally soiled garments.

Whites - For white fabrics with or without bleach.

Perm Press - For wash-and-wear, synthetic fabrics, and lightly to normally soiled garments.

Delicates/Hand Wash - For sheer fabrics, bras, lingerie silk, and other handwash-only fabrics. For

best results, use liquid detergent.

Wool - For machine-washable wool. Loads should be under 8 pounds.

_ The wool wash cycle of this machine has been approved by Woolmark for the

washing of machine washable Woolmark products provided that the products are

washed according to the instructions on the garment label and those issued by

_k_o_,xt_ K the manufacturer of this washing machine, M0509.

QuickWash - For lightly soiled garments needed quickly.

Towels - For bath towels and washcloths. Due to their high absorbancy, wash no more than a half

load (6 pounds) of towels at a time for best results

Sanitize -For heavily soiled, colorfast garments.This cycle heats the water to 150°F to eliminate

bacteria.

NOTE: If Pause is selected during the heating portion of the Sanitize Cycle, your Washer door will

remain locked for your safety.

Bedding - For bulky items such as blankets and sheets.

ActiveWear - For washable sportswear.

E¢oWash - For geographic areas where energy and water conservation is needed. It saves an

additional 5% of Energy and 5% of water consumption.

Rinse + Spin - Use for loads that need rinsing only or to add rinse-added fabric softener to a load.

Spin Only- Provides a spin to remove more water.

Start/Pause se_÷ctio_ butto_

Press to pause and restart programs.

Power button

Press once to turn your Washer on, press again to turn your Washer off. If left on for more than 10

minutes without any buttons being touched, the power automatically turns off.

NOTE_ Cycles and options vary by model. Refer to cycle chart in Appendix.

C-3 SAMSUNG CIothesWasherOwner'slnstructions

Washing a Load of Laundry

CHILD LOCK

A function that prevents children from playing with your Washer.

ACT_VAT_NG!D£ACT_VATING

If you want to activate/deactivate the Child Lock function, press the Soil Level and Signa[ buttons at the

same time for 3 seconds.

How _ Wor_:

1. Child Lock can be activated while your Washer is running.

2. Once you activate Child Lock, ai[ controls (except for the Power button) wii[ be locked until you

deactivate Child Lock.

3. The Child Lock button will be lit while it is in effect.

Note: When buttons, other than the Power button, do not respond, please check if the Child

Lock function is on.

GARMENT +

You can add or take out laundry items even after the wash has started, as long as the Garment+ light is

on. Pushing the Start/Pause button unlocks the door, unless the water is too hot or if there is too much

water in your Washer. If you are able to unlock the door and wish to continue the wash cycle, close the

door and press the Start/Pause button.

MY CYCLE

Allows you to activate your custom wash (temperature, spin, soil level, etc.) with one-button

convenience.

By pushing the My Cycle button, you activate the settings used during the last My Cycle mode.The My

Cycle light will indicate activation.

You ¢_n sele_'t air oD_'io_s as fJIows _n My CyUe mode°

1. Select cycle using Cycle Selector dial.

2. After cycle selection, set each option.

Note: At this time, the option will follow as per each cycle's default option selection.

3. Then, you can start My Cycle by pushing the Start/Pause button in My Cycle mode.

The cycle and options you select will be displayed next time you choose My Cycle.

Note: You can change My Cycle setting by repeating same process above.

The last used setting will be displayed at the next time you choose My Cycle.

SAMSUNG CIothesWasherOwner'slnstructions C-4

Washing a Load of Laundry

FOR SILVERCARETM WASHING (select models)

An increased consumer demand for energy-saving products prompted Samsung to develop a system to

use silver, widely known for its antimicrobial properties, as a sanitizing agent in your washing machine.

Pure silver atoms have an electron stripped away by electrolysis during the wash and rinse cycles, which

releases up to 16 million trillion silver ions that then penetrate deep into the fabric to sanitize clothing

(according to U.S. EPA Test Guideline DIS/TSS-13) without the need for hot water or bleach.

Here's how it works: A grapefruit-sized device alongside the tub uses two pure silver plates the size of

large chewing gum sticks as electrodes in the water inlet system.The resulting positively charged silver

atoms - Silver ions (Ag+) -- are sprayed into the tub during the wash and final rinse cycle.

This process removed or killed greater than 99.9% of tested bacteria.

Samsung's SilverCareT_Technology provides a 92% energy savings over hot water sanitization. Extra

delicate blouses, shirts, or even lingerie that can't be washed in hot water can now be sanitized

effectively without the adverse effects of hot water sanitization that is normally a concern with those

types of articles.The silver plates carry a warranty often years, and can easily be replaced by a Service

Technician if so needed.

1. Load the washer.

2. Press the Power button.

3o Select a Cycle by turning the Cycle Selection dial.

4o Press SilverCare TM button.

5° Add detergent in the dispenser tray f_r main washing_ and add fabric s__ener up t_ the marked _ine.

6° Press the Start/Pause button.

:The washer automatically selects optimal washing conditions by sensing the laundry's weight.

Note

FOR HOME USEONLY- COMMERCIAL USERS SHOULD NOTIFY THEIR LOCAL WASTE TREATMENT

AUTHORITIES BEFORE USE

The total number of silver cycles run by the washer is displayed when pushing the Signal button and the

SilverCare TM button.

LU3 : less than 1000 times

LU2 : between 1000 to 2000 times

LU 1 : between 2000 to 2999 times

LUO : over 2999 times

You should replace the SilverCare TM kit when the display reads"LU0"as the electrodes are near the end of

their useful life. Contact 1-800-SAMSUNG.

Note

For some models that have no heater if you choose SilverCare TM, the temperature will be automatically

set to to Cold/Cold.

You cannot choose the SilverCare TM option with the Wool cycle.

C-5 SAMSUNG CIothesWasherOwner'slnstructions

Washing a Load of Laundry

DETERGENTUSE

Your Washer isdesigned to use high efficiency (HE) detergents.

For best cleaning results, use a high efficiency detergent such as -fide HE, Wisk

HE, Cheer HE or Gain HE_.High efficiency detergents contain suds suppressors

that reduce or eliminate suds. When fewer suds are produced, the load tumbles

more efficiently and cleaning is maximized.

!WARNING

Regular detergent is Not recommended. Please use only HE detergent.

NOTE: Reducing the amount of detergent may reduce cleaning. It is important to pre-treat stains, sort

carefully by color and soil level, and avoid overloading.

_ Brand names are trademarks of their respective manufacturers.

FEATURES

AUTOMATIC DJS?ENSER

YourWasher has separatecompartments fordispensing

detergentand color-safebleach,chlorinebleach,and fabric

softener,Alllaundryadditivesareadded totheirrespective Prewash(selectmodels)

compartments beforestartingyour Washer,

The automatic dispenserMUST ALWAYS be inplacebefore

starting your Washer.

DO NOT open the automatic dispenser when your Washer is

running.

To u_e:

I. Pull out the dispenser drawer on the left side of the

control panel.

2. Add recommended quantity of additive to the

appropriate compartments with laundry additives, being

careful not to overfill or spill.

3. Slide the dispenser drawer carefully and completely back into the compartment.

DETERGENT CO_PARTMENT

1. Pour the recommended amount of laundry detergent directly into the detergent compartment

before starting your Washer.

2. If color-safe bleach is to be used, it should be added with detergent to the detergent

compartment.

• When adding color-safe bleach with detergent, it is best if both laundry products are in the

same form - granular or liquid.

NOTE: If using liquid detergent, lower the detergent selector and add the detergent to the

detergent compartment.

SAMSUNG CIothesWasherOwner'slnstructions C-6

Washing a Load of Laundry

PREWASH COMPARTMENT (SELECTMODELS)

When using the Pre Wash option (select models), detergent should be added to both the Pre Wash

compartment and the detergent compartment.The detergent will automatically be dispensed during

Pre Wash.

• If high efficiency (HE) detergent is used, add 1/3 of the recommended amount to the Pre Wash

compartment and 2/3 of the recommended amount to the detergent compartment.

BLEACH COMPARTMENT

(Liquid chlorine bleach only)

1. Add chlorine bleach to the bleach compartment. _ Bleach

DO NOT exceed the MAX FILL line. _Compartment

2. Avoid splashing or over-filling the compartment. I Fabric Softner

3. Your Washer automatically dispenses bleach into the tub Compartment

at the appropriate time.

4. The dispenser automatically dilutes liquid chlorine

bleach before it reaches the wash load.

NOTES:

• Never pour undiluted liquid chlorine bleach directly

onto the load or into the tub. It is a powerful chemical

and can cause fabric damage, such as weakening of

the fibers or color loss, if not used properly.

If you prefer to use color-safe, non-chlorine bleach, add it to the appropriate detergent

compartment.

DO NOT pour color-safe bleach into the chlorine bleach dispenser.

FABRIC SOFTENERCOMPARTMENT

1. Pour the recommended amount of liquid fabric softener into the softener compartment.

For smaller loads, use less than one capful.

2. Fabric softener should be diluted with water until it reaches MAX FILL in the compartment.

3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse

cycle.

NOTES:

• Use the softener compartment ONLY for liquid fabric softeners.

• DO NOT use the Downy BalP with this Washer. It will not add fabric softener at the appropriate

time.

Use the automatic dispenser.

Brand names are trademarks of their respective manufacturers.

C-7 SAMSUNG Clothes Washer Owner's lnstructions

CLEANINGTHE EXTERIOR

Turn offthe water faucets after finishing the day's washing.

This will shut off the water supply to your Washer and prevent the unlikely possibility of damage from

escaping water. Leave the door open to allow the inside of your Washer to dry out.

Use a soft cloth to wipe up all detergent, bleach or other spills as they occur.

C'lean _e following _ recommended:

Control Panel - Clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads.

Do not spray cleaners directly on the panel.

Cabinet- Clean with soap and water.

CLEANINGTHE iNTERiOR

Clean the interior of your Washer periodically to remove any dirt, soil, odor, mold, mildew, or bacterial

residue that may remain in your Washer as a result of washing clothes.

Failure to follow these instructions may result in unsatisfactory conditions, including unpleasant odor

and/or permanent stains on your Washer or laundry.

Hard water deposits may be removed, if needed. Use a cleaner labeled "Washer safe".

CLEANINGTHE DISPENSERS

The Automatic Dispenser may need to be cleaned periodically due to

laundry additive buildup.

1. Press the release lever on the inside of the dispenser and pull out.

2. Remove the cups from the fabric softener and bleach compartments.

3. Wash all of the parts under running water.

4. Clean the dispenser recess with a soft brush.

5. Reinsert the cups, pushing them firmly into place.

6. Push the dispenser back into place.

7. Run a Rinse & Spin cycle without any load in your Washer.

STORINGYOLIRWASNER

Washers can be damaged if water isnot removed from hoses and internal components before storage.

Prepare your Washer for storage as follows:

• Select the Quick Wash cycle and add bleach to the automatic dispenser. Run your Washer through

the cycle without a load.

• Turn the water faucets offand disconnect the inlet hoses.

• Unplug your Washer from the electrical outlet and leave your Washer door open to let air circulate

inside the tumbler.

• If your Washer has been stored in below-freezing temperatures, allow time for any leftover water in

your Washer to thaw out before use.

SAMSUNG CIothesWasherOwner'slnstructions D-1

CHECKTHESEPOINTS iFYOURWASHER..

will not start..

has no water or not

enough water..

has detergent remains

in the automatic

dispenser after the

wash cycle iscomplete.

vibrates or is too noisy.

stops

• Make suredoor is firmly closed.

• Make sureyour Washer is plugged in.

• Make sure the water source faucets are turned on.

• Make sure to press the Cycle Selector dial to start your Washer.

• Make sure the Child Lock is not activated; see page C4.

• Before your Washer starts to fill, it will make a series of clicking noises

to check the door lock and do a quick drain.

• Turn both faucetson fully.

Make sure the door is tightly closed.

Straighten water inlet hoses.

Disconnect hoses and clean screens. Hose filter screens may be

plugged.

Open and close the door, then press the Cycle Selector dial.

Make sure your Washer is running with sufficient water pressure.

Make sure the Detergent Selector dial is in the upper position when

using granular detergent.

Make sure your Washer isset on a level surface. If the surface isnot

level, adjust your Washer feet to level the appliance.

Make sure that the shipping bolts are removed.

Make sure your Washer isnot touching any other object.

Make sure the laundry load isbalanced.

Plug cord into live electrical outlet.

Check fuse or reset circuit breaker.

Close door and press the Cycle Selector dial to start your Washer. For

your safety, your Washer will not tumble or spin unless the door is

closed.

Before your Washer starts to fill, it will make a series of clicking noises

to check the door lock and do a quick drain.

There may be a pause or soak period in the cycle. Wait briefly and it

may start.

Check screens on inlet hoses at the faucets for obstructions. Clean

screens periodically.

E-1 SAMSUNG Clothes Washer Owner's lnstructions

fills with the wrong

temperature water.

door lockedshut or

will not open.

does not drain and/or

spin.

load is too wet at the

end of the cycle.

leaks water.

has excessive suds.

+ Turn both faucetson fully.

+ Make sure temperature selection iscorrect.

+ Make sure hoses are connected to correct faucets. Flush water lines.

+ Check the water heater. It should be set to deliver a minimum 120 °

F (49° C) hot water at the tap. Also check water heater capacity and

recovery rate.

+ Disconnect hoses and clean screens. Hose filter screens may be

plugged.

+ As your Washer is filling, the water temperature may change as

the automatic temperature control feature checks incoming water

temperature.This is normal.

+ While your Washer is filling, you may notice just hot and/or just

cold water going through the dispenser when cold or warm wash

temperatures are selected.This isa normal function of the automatic

temperature control feature as your Washer determines the

temperature of the water.

+ Press the Cycle Selector dial to stop your Washer.

+ Your Washer door will remain locked during the heating portion of the

Sanitize Cycle

+ It may take a few moments for the door lock mechanism to disengage.

+ Check fuseor reset circuit breaker.

+ Straighten drain hoses. Eliminate kinked hoses. If there isa drain

restriction, call for service.

+ Close the door and press the Cycle Selector dial. For your safety, your

Washer will not tumble or spin unless the door isclosed.

+ Use the High or Extra High spin speed.

+ Use high efficiency detergent to reduce over-sudsing.

+ Load is too small.Very small loads (one or two items) may become

unbalanced and not spin out completely.

+ Make suredoor is firmly closed.

+ Make sure hoseconnections are tight.

+ Make sure end of drain hose is correctly inserted and secured to drain

facility.

Avoid overloading.

Use high efficiency detergent to prevent over-sudsing.

Reduce detergent amount for soft water, small or lightly soiled loads.

Non-HE detergent isNOT recommended.

SAMSUNG CIothesWasherOwner'slnstructions E-2

iNFORMATiON CODES

Information codes may be displayed to help you better understand what isoccurring with your Washer.

Code Symbol Meaning Solution

_l_ Unbalanced load prevented your Redistribute the load, press the Cycle SelectorWasher from spinning, dial.

d[_ Door is unlocked when Washer Press the Power button to turn offyour Washer,

isrunning, then restart the cycle. If the code reappears,

call for service. See below.

m Door isopen when Washer is Close the door tightly and restart the cycle.

Imi _! running. If the code reappears, call for service.

Iml ml

See below.

Iw _ Your Washer failed to lock the Close the door tightly and restart the cycle.

--Jm_m door. If the code reappears, call for service.

See below.

Water temperature control Call for service. See below.

I_[I m problem.

(Heater Control problem)

[ [m Your Washer has tried to fill but Call for service. See below.

_ 1_ has not reached the proper water

level.

_ The door will not unlock. Make sure the door isfirmly closed.

IroN Push the Power button to turn offyour Washer,

then turn it on again. If the code reappears, call

for service. See below.

Im _ Motor not running properly. Restart the cycle pressing the Cycle Selector

1_ _ dial. If the code reappears, call for service.

See below.

_w[|l_i Your washer is not draining. Before calling for service, check the following.

But, it can light up when the unit 1)Turn off the unit and turn it on again.

senses a brief restriction while 2) Select the Spin Only

draining. 3) Press the Start/Pause to drain the water.

If it still does not drain, call for service.

F Your Washer has tried to fill but Make sure the water faucets are open all the

_ was unsuccessful, way. Check for kinked hoses.

Check inlet screens on fill hoses.

E-3 SAMSUNG CIothesWasherOwner'slnstructions

CodeSymbol

SI-

iqF

I--i

II-

31-

-IF

L-U-

ql:_

I-II IL-

DuO 3

Meaning

Problem with control.

Electric service was lost when

Washer was running.

A fault is detected in the water

level sensor.

Jammed Key.

Motor speed sensor problem.

Temperature sensor problem.

High current detected.

High/Low voltage detected.

Vibration sensor problem.

SilverCare TM control problem

Too much suds is detected

during the washing session. And,

the unit is put on hold until the

suds get reduced.Then, it will go

back to the operation. When it

finishes washing, End and SUdS

codes will blink in turn.

For any codes not listed above, call 1-800-726-7864

Solution

Call for service. See below.

Restart the cycle by pressing the Cycle Selector

dial.

Call for service

Restart the cycle.