G466-001-200801_463367016_ENG_FRE_SPA

08/27/15 • G466-001-200801

If you have questions or need assistance

during assembly, please call 1-888-430-7870.

Si vous avez des questions ou besoin d´aide

pendant l’assemblage, S’il vous plaît appelez

1-888-430-7870

Si tiene alguna pregunta o si Necesita

ayuda durante el Ensamblado, llámenos Al

1-888-430-7870

Serial number | Numéro de série | Número de serie

Date purchased | Date d’chat | Fecha de compra

See rating Label on grill for serial number.

El número de serie se encuentra en la etiqueta de

especificaciones de la parrilla.

Ce numéro se trouve sur l´étiquette signalétique sur

i´appareil.

463367016

Professional

3-Burner Gas Grill

#4584609

Convertit facilement de forme (LP)

propane liquide (NG) de gaz naturel

ENSEMBLE DE CONVERSION

TABLE OF CONTENTS

For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Use and Care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-45

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-47

Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Hardware List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Registration Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Tools needed for assembly:

Adjustable wrench (not provided)

Screwdriver (not provided)

7/16" Combination wrench (not provided)

If during operation the flames go out (You smell gas or

cannot see the flame)

1. Turn the burner controls OFF

2. Open lid.

3. Wait 5 minutes and repeat the lighting procedure.

If the burner goes out, gas will continue to flow out of the

burner and could accidently ignite with risk of injury.

DANGER

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

CAUTION

CAUTION: Indicates a potentially hazardous situation or

unsafe practice which, if not avoided, may result in minor

or moderate injury.

SAFETY SYMBOLS

The symbols and boxes shown below explain what each

heading means. Read and follow all of the messages found

throughout the manual.

THIS GRILL IS FOR OUTDOOR USE

ONLY.

INSTALLER/ASSEMBLER:

Leave this manual with consumer.

CONSUMER:

Keep this manual for future reference.

For residential use only. Do not use for commercial cooking.

WARNING

DANGER

If you smell gas:

1. Shut off gas to the appliance

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the appliance and

immediately call your gas supplier or your fire

department.

WARNING

1. Do not store or use gasoline or other flammable

liquids or vapors in the vicinity of this or any other

appliance.

2. An LP cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

CAUTION

WARNING

Do not attempt to repair or alter the

hose/valve/regulator for any “assumed” defect. Any

modification to this assembly will void your

warranty and create the risk of a gas leak and fire.

Use only authorized replacement parts supplied by

manufacturer.

DANGER

WARNING

Do not cover grates with aluminum foil or any other

material. This will block burner ventilation and

create a potentially dangerous condition resulting in

property damage and/or personal injury.

Failure to follow all manufacturer’s instructions could result in

serious personal injury and/or property damage.

WARNING

Read and follow all safety statements, assembly

instructions, and use and care directions before attempting

to assemble and cook.

CAUTION

Some parts may contain sharp edges. Wear protective

gloves if necessary.

CAUTION

Grease Fires

• Putting out grease fires by closing the lid is not possible.

Grills are well ventilated for safety reasons.

• Do not use water on a grease fire. Personal injury may

result. If a grease fire develops, turn knobs and LP

tank off.

• If grill has not been regularly cleaned, a grease fire can

occur that may damage the product. Pay close attention

while preheating or burning off food residue to insure

that a grease fire does not develop.

• The best way to prevent grease fires is

regular cleaning of the grill following

instructions on General Grill Cleaning and

Cleaning The Burner Assembly.

CAUTION

Using pots larger than 6 quarts in capacity could exceed

weight limit of the side burner shelf or side shelf, resulting

in failure of grill cart components.

DANGER

•

NEVER store a spare LP cylinder under or near the

appliance or in an enclosed area.

•

Never fill a cylinder beyond 80% full.

If you see, smell or hear gas escaping, immediately get

away from the LP cylinder/appliance and call your fire

department.

•

An over filled or improperly stored cylinder is a hazard

due to possible gas release from the safety relief valve.

This could cause an intense fire with risk of property

damage, serious injury or death.

•

WARNING

CALIFORNIA PROPOSITION 65

1. Combustible by-products produced when using this

product contains chemicals known to the State of

California to cause cancer, birth defects, or other

reproductive harm.

2. This product contains chemicals, including lead and

lead compounds, known to the State of California to

cause cancer, birth defects or other reproductive harm.

Wash your hands after handling this product.

Installation Safety Precautions

•Use grill, as purchased, only with LP (propane) gas and the

regulator/valve assembly supplied. If your grill is Dual Fuel

ready, a conversion kit must be purchased for use with

natural gas.

•Grill installation must conform with local codes, or in their

absence of local codes, with either the National Fuel Gas

Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane

Installation Code, CSA B149.1, or Propane Storage and

Handling Code, B149.2.

•All electrical accessories (such as rotisserie) must be

electrically grounded in accordance with local codes, or

National Electrical Code, ANSI / NFPA 70 or Canadian

Electrical Code, CSA C22.1. Keep any electrical cords

and/or fuel supply hoses away from any hot surfaces.

•This grill is safety certified for use in the United States

and/or Canada only. Do not modify for use in any other

location. Modification will result in a safety hazard.

USE AND CARE

LP Cylinder Removal, Transport and Storage

•Turn OFF all control knobs and LP cylinder valve. Turn coupling

nut counterclockwise by hand only - do not use tools to

disconnect. Loosen cylinder screw beneath bottom shelf or

disconnect other retention means, then lift LP cylinder up and

and out of cart. Install safety cap onto LP cylinder valve.

Always use cap and strap supplied with valve. Failure to use

safety cap as directed may result in serious personal

injury and/or property damage.

•A disconnected LP cylinder in storage or being transported

must have a safety cap installed (as shown). Do not store an

LP cylinder in enclosed spaces such as a carport, garage,

porch, covered patio or other building. Never leave an LP

cylinder inside a vehicle which may become overheated by the

sun.

•Do not store an LP cylinder in an area where children play.

LP Cylinder Valve

Retainer Strap

Safety Cap

LP Cylinder

•The LP cylinder used with your grill must meet the

following requirements:

•Use LP cylinders only with these required measurements: 12"

(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.)

capacity maximum.

•LP cylinders must be constructed and marked in accordance

with specifications for LP cylinders of the U.S. Department of

Transportation (DOT) or for Canada, CAN/CSA-B339, cylinders,

spheres and tubes for transportation of dangerous goods,

Transport Canada (TC). See LP cylinder collar for marking.

•LP cylinder valve must have:

•Type 1 outlet compatible with

regulator or grill.

•Safety relief valve.

•UL listed Overfill Protection Device (OPD). This

OPD safety feature is identified by a unique

triangular hand wheel. Use only LP cylinders

equipped with this type of valve.

OPD Hand

Wheel

•LP cylinder must be upright for vapor withdrawal and include

collar to protect LP cylinder valve. Always keep LP cylinders in

upright position during use, transit or storage.

LP cylinder in upright position

for vapor withdrawal

LP (Liquefied Petroleum Gas)

•LP gas is nontoxic, odorless and colorless when produced. For

Your Safety, LP gas has been given an odor (similar to rotten

cabbage) so that it can be smelled.

•LP gas is highly flammable and may ignite unexpectedly when

mixed with air.

LP Cylinder Filling

•Use only licensed and experienced dealers.

•LP dealer must purge new cylinder before filling.

•Dealer should NEVER fill LP cylinder more than 80% of LP

cylinder volume. Volume of propane in cylinder will vary by

temperature.

•A frosty regulator indicates gas overfill. Immediately close

LP cylinder valve and call local LP gas dealer for assistance.

•Do not release liquid propane (LP) gas into the atmosphere.

This is a hazardous practice.

•To remove gas from LP cylinder, contact an LP dealer or call a

local fire department for assistance. Check the telephone

directory under “Gas Companies” for nearest certified LP

dealers.

WARNING

If “growing” bubbles appear, do not use or move the LP

cylinder. Contact an LP gas supplier or your fire department!

2.Turn all control knobs to the OFF position.

Do not use a POL transport

plug (plastic part with external

threads)! It will defeat the

safety feature of the valve.

6.Turn the coupling nut clockwise and tighten to a full stop. The

regulator will seal on the back-check feature in the LP cylinder

valve, resulting in some resistance. An additional one-half to

three-quarters turn is required to complete the

connection. Tighten by hand only – do not use tools.

NOTE:

If you cannot complete the connection, disconnect regulator

and repeat steps 5 and 6. If you are still unable to complete the

connection, do not use this regulator!

DANGER

• Do not insert any tool or foreign object into the valve outlet or

safety relief valve. You may damage the valve and cause a

leak. Leaking propane may result in explosion, fire, severe

personal injury, or death.

LP Cylinder Exchange

LP Cylinder Leak Test

For your safety

•Many retailers that sell grills offer you the option of replacing

your empty LP cylinder through an exchange service. Use only

those reputable exchange companies that inspect, precision fill,

test and certify their cylinders. Exchange your cylinder only

for an OPD safety feature-equipped cylinder as described

in the "LP Cylinder" section of this manual.

•Always keep new and exchanged LP cylinders in upright

position during use, transit or storage.

•Leak test new and exchanged LP cylinders BEFORE

connecting to grill.

•Place safety cap on cylinder valve outlet whenever the cylinder

is not in use. Only install the type of safety cap on the cylinder

valve outlet that is provided with the cylinder valve. Other types

of caps or plugs may result in leakage of propane.

•Leak test must be repeated each time LP cylinder is

exchanged or refilled.

•Do not smoke during leak test.

•Do not use an open flame to check for gas leaks.

•Grill must be leak tested outdoors in a well-ventilated area,

away from ignition sources such as gas fired or electrical

appliances. During leak test, keep grill away from open flames

or sparks.

•Use a clean paintbrush and a 50/50 mild soap and water

solution. Brush soapy solution onto areas indicated by arrows in

figure below.

• Do not use household cleaning agents. Damage to gas train

components can result.

5.Hold regulator and insert nipple into LP

cylinder valve. Hand-tighten the coupling

nut, holding regulator in a straight line with

LP cylinder valve so as not to cross-thread

the connection.

4.Remove the safety cap from LP cylinder valve. Always use cap

and strap if supplied with valve.

3.Turn LP cylinder OFF by turning hand-wheel clockwise to a full

stop.

1.LP cylinder must be properly secured onto grill. (Refer to

assembly section.)

Connecting Regulator to the LP Cylinder

Straig

Hold coupling nut and regulator

as shown for proper connection

to LP cylinder valve.

Coupling nut

Nipple has to be

centered into the LP

cylinder valve.

Safety Relief

Valve

OPD Hand

Wheel

Type 1 outlet

with thread

on outside

Strap and Cap

• If you notice grease or other hot material dripping from grill

onto valve, hose or regulator, turn off gas supply at once.

Determine the cause, correct it, then clean and inspect valve,

hose and regulator before continuing. Perform a leak test.

• Keep ventilation openings in cylinder enclosure (grill cart) free

and clear of debris.

• Do not store objects or materials inside the grill cart enclosure

that would block the flow of combustion air to the underside of

either the control panel or the firebox bowl.

• The regulator may make a humming or whistling noise during

operation. This will not affect safety or use of grill.

• If you have a grill problem see the "Troubleshooting” Section.

• If the regulator frosts, turn off grill and LP cylinder valve

immediately. This indicates a problem with the cylinder and it

should not be used on any product. Return to supplier!

Leak Testing Valves, Hose and Regulator

1.Turn all grill control knobs to OFF.

2.Be sure regulator is tightly connected to LP cylinder.

3.Completely open LP cylinder valve by turning hand wheel

counterclockwise. If you hear a rushing sound, turn gas off

immediately. There is a major leak at the connection. Correct

before proceeding.

4.Brush soapy solution onto areas circled below, or other similar

fittings on your grill.

5.If “growing” bubbles appear, there is a leak. Close LP cylinder

valve immediately and retighten connections. If leaks cannot be

stopped do not try to repair. Call for replacement parts.

6.Always close LP cylinder valve after performing leak test by

turning hand wheel clockwise.

NOTE: Sideburner shelf

fascia and other parts not

shown for clarity.

• Outdoor gas appliance is not intended to be installed in or

on a boat.

• Outdoor gas appliance is not intended to be installed in or on

an RV.

• Never attempt to attach this grill to the self-contained LP

gas system of a camper trailer or motor home.

NOTE: Your grill may NOT

be equipped with a

sideburner.

WARNING

Safety Tips

• Before opening LP cylinder valve, check the coupling nut for

tightness.

• When grill is not in use, turn off all control knobs and LP

cylinder valve.

• Never move grill while in operation or still hot.

• Some surfaces will be hot during use. Use long-handled

barbecue utensils and oven mitts to avoid burns and splatters.

• Maximum load for sideburner and side shelf is 10 lbs.

• The grease tray or cup must be installed during use and

emptied after each use. Do not remove grease tray or cup

until grill has completely cooled.

• Clean grill often, preferably after each cookout. If a bristle

brush is used to clean any of the grill cooking surfaces, ensure

no loose bristles remain on cooking surfaces prior to grilling. It

is not recommended to clean cooking surfaces while grill is hot.

• Do not use grill until leak-tested.

• If a leak is detected at any time, STOP! Turn off

gas at source and correct leak.

• If you cannot stop a gas leak by closing the LP cylinder valve

leave area and call your fire department!

WARNING

• Do not lean over grill while lighting.

1. Turn gas burner control valves to (off).

2. Open lid during lighting or re-lighting.

3. Turn ON gas at LP cylinder.

WARNING

For Safe Use of Your Grill and to Avoid Serious Injury:

• Do not let children operate or play near grill.

• Keep grill area clear and free from materials that burn.

• Do not block holes in sides or back of grill.

• Check burner flames regularly.

• Do not use charcoal or ceramic briquets in a gas grill.

• Use grill only in well-ventilated space. NEVER use in

enclosed space such as carport, garage, porch, covered

patio, or under an overhead structure of any kind.

• Do not cover grates with aluminum foil or any other

material. This will block burner ventilation and create a

potentially dangerous condition resulting in property

damage and/or personal injury.

• Use grill at least 3 ft. from any wall or surface. Maintain

10 ft. clearance to objects that can catch fire or sources of

ignition such as pilot lights on water heaters, live electrical

appliances, etc.

• Apartment Dwellers:

Check with management to learn the requirements and fire

codes for using an LP gas grill in your apartment complex.

If allowed, use outside on the ground floor with a three (3)

foot clearance from walls or rails. Do not use on or under

balconies.

• NEVER attempt to light or re-light burner with lid

closed. A buildup of non-ignited gas inside a closed

grill is hazardous.

• Never operate grill with LP cylinder out of correct

position specified in assembly instructions.

• Always close LP cylinder valve and remove coupling nut

before moving LP cylinder from specified operation

position.

3 ft.

Ignitor Lighting

Match-Lighting

If ignition does NOT occur in 5 seconds, turn the burner

controls off, wait 5 minutes and repeat the lighting

procedure. If the burner does not ignite with the valve

open, gas will continue to flow out of the burner and

could accidently ignite with risk of injury.

Turn controls and gas source or tank OFF when not

in use.

4. Place match into match holder (hanging from side panel of

grill). Light match; then light burner by placing match through

the match light hole on side of grill. Immediately push in and

turn burner knob to the HIGH position. Be sure burner lights

and stays lit.

CAUTION

WARNING

• Do not lean over grill while lighting.

1. Turn gas burner control valves to (off).

2. Open lid during lighting or re-lighting.

3. Turn ON gas at LP cylinder.

4. To ignite, push and turn burner knob to HIGH. Immediately,

push and hold ELECTRONIC IGNITOR button until the burner

lights.

5. If ignition does NOT occur in 5 seconds, turn the burner

controls off , wait 5 minutes and repeat the lighting

procedure.

6. Repeat steps 4 and 5 to light other main burners.

5. Light adjacent burners in sequence by pushing knobs in and

turning to the HIGH position.

• Before each use, check to see if hoses are cut or worn or

kinked. Replace damaged hoses before using grill. Use only

valve/hose/regulator specified by manufacturer.

Hose Check

• Important: Make sure gas is off at LP cylinder before

checking valves. Knobs lock in off position. To check valves,

first push in knobs and release, knobs should spring back. If

knobs do not spring back, replace valve assembly before using

grill. Turn knobs to LOW position then turn back to off position.

Valves should turn smoothly.

Valve Check

• Turn gas off at LP cylinder. Press and hold electronic ignitor

button. "Click" should be heard and spark seen each time in

each collector box or between burner and electrode. See

"Troubleshooting" if no click or spark.

Ignitor Check

• Turn all knobs to the off position. Turn LP cylinder off by

turning hand-wheel clockwise to a full stop.

Turning Grill Off

• Remove cooking grates and heat tents. Light burners, rotate

knobs from HIGH to LOW. You should see a smaller flame in

LOW position than seen on HIGH. Perform burner flame check

on side burner, also. Always check flame prior to each use. If

only low flame is seen refer to "Sudden drop or low flame" in

the Troubleshooting Section.

HIGH

LOW

Burner Flame Check

Sideburner Ignitor Lighting

• Do not lean over grill while lighting.

4. Turn sideburner knob to the HIGH position, push and hold

ELECTRONIC IGNITOR button.

5. If sideburner does NOT light within 5 seconds, turn knob

to off, wait 5 minutes, then repeat lighting procedure.

Sideburner Match Lighting

4. Place lit match near burner. Immediately turn sideburner

knob to the HIGH position. Be sure burner lights and stays

lit.

NOTE: Your grill may NOT be equipped with a

Sideburner!

Storing Your Grill

• Clean cooking grates.

• Store in dry location.

• When LP cylinder is connected to grill, store outdoors in a

well-ventilated space and out of reach of children.

• Cover grill if stored outdoors. Choose from a variety of grill

covers offered by manufacturers.

• Store grill indoors ONLY if LP cylinder is turned off and

disconnected, removed from grill and stored outdoors.

• When removing grill from storage, follow “Cleaning the

Burner Assembly” instructions before starting grill.

2. Open lid during lighting or re-lighting.

• Do not lean over grill while lighting.

3. Turn ON gas at LP cylinder.

1. Turn gas burner control valves to (off).

2. Open lid during lighting or re-lighting.

3. Turn ON gas at LP cylinder.

1. Turn gas burner control valves to (off).

General Grill Cleaning

• Do not mistake brown or black accumulation of grease and

smoke for paint. Interiors of gas grills are not painted at the

factory (and should never be painted). Apply a strong solution

of detergent and water or use a grill cleaner with scrub brush on

insides of grill lid and bottom. Rinse and allow to completely air

dry. Do not apply a caustic grill/oven cleaner to painted

surfaces.

• Plastic parts: Wash with warm soapy water and wipe dry.

• Do not use citrisol, abrasive cleaners, degreasers or a

concentrated grill cleaner on plastic parts. Damage to and

failure of parts can result.

• Porcelain surfaces: Because of glass-like composition, most

residue can be wiped away with baking soda/water solution or

specially formulated cleaner. Use nonabrasive scouring

powder for stubborn stains.

• Painted surfaces: Wash with mild detergent or nonabrasive

cleaner and warm soapy water. Wipe dry with a soft

nonabrasive cloth.

• Stainless steel surfaces: To maintain your grill’s high quality

appearance, wash with mild detergent and warm soapy water

and wipe dry with a soft cloth after each use. Baked-on

grease deposits may require the use of an abrasive plastic

cleaning pad. Use only in direction of brushed finish to avoid

damage. Do not use abrasive pad on areas with graphics.

• Cooking surfaces: If a bristle brush is used to clean any of

the grill cooking surfaces, ensure no loose bristles remain on

cooking surfaces prior to grilling. It is NOT recommended to

clean cooking surfaces while grill is hot.

SPIDER ALERT!

CAUTION

INSIDE BURNER

SPIDER AND WEBS

If your grill is getting hard to light or the flame is weak,

check and clean the venturis and burners.

Spiders or small insects are known to create “flashback”

problems by building nests and laying eggs in the grill’s

venturi or burner, obstructing the flow of gas. The back-

up gas can ignite behind the control panel. This

flashback can damage your grill and cause injury. To

prevent flashbacks and ensure good performance the

burner and venturi tube assembly should be removed

and cleaned when ever the grill has been idle for an

extended period of time.

Cleaning the Burner Assembly

Follow these instructions to clean and/or replace parts of burner

assembly or if you have trouble igniting grill.

1. Turn gas off at control knobs and LP cylinder.

2. Remove cooking grates and heat tents.

3. Remove carryover tubes and hardware securing burners.

4. Detach electrode from burner.

NOTE: Removal/Detachment method will depend on the

burner configuration. See different configurations in

illustrations below.

5. Carefully lift each burner up and away from valve openings.

We suggest three ways to clean the burner tubes. Use

the one easiest for you.

(A) Bend a stiff wire (a light weight coat hanger works well)

into a small hook. Run the hook through each burner

tube several times.

(B) Use a narrow bottle brush with a flexible handle (do not

use a brass wire brush). Run the brush through each

burner tube several times.

the burner tube and out the burner ports. Check each port

to make sure air comes out each hole.

6. Wire brush entire outer surface of burner to remove food

residue and dirt.

7. Clean any blocked ports with a stiff wire such as an open

paper clip.

8. Check burner for damage due to normal wear and corrosion,

some holes may become enlarged. If any large cracks or holes

are found, replace burner.

VERY IMPORTANT: Burner tubes must reengage

valve openings. See illustrations at right.

Correct burner-to-

valve engagement

9. Attach electrode to burner.

10. Carefully replace burners.

11. Attach burners to brackets on firebox.

12. Reposition carryover tubes and attach to burners. Replace

heat tents and cooking grates.

13. Before cooking again on grill, perform a “Leak Test” and

“Burner Flame Check”.

Your burner might be different

Electrode

Pry off electrode with

a flate blade

screwdriver

Electrode

Firebox

Carryover tube

Firebox Burner

Support

Remove

screws

Firebox

Firebox Burner

Support

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this

product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods

indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or

freight pre-paid by the consumer for review and examination.

*Note: A dated sales receipt WILL be required for warranty service.

The original consumer-purchaser will be responsible for all shipping charges for parts replaced under the terms of this limited warranty.

This limited warranty is applicable in the United States and Canada only, is only available to the original owner of the product and is not transferable.

Manufacturer requires proof of your date of purchase. Therefore, you should retain your sales slip or invoice. Registering your product is not a

substitute for proof of purchase and the manufacturer is not responsible for or required to retain proof of purchase records.

This limited warranty applies to the functionality of the product ONLY and does not cover cosmetic issues such as scratches, dents, corrosions or

discoloring by heat, abrasive and chemical cleaners or any tools used in the assembly or installation of the appliance, surface rust, or the

discoloration of stainless steel surfaces. Paint is not warranted and will require touch up. RUST is not considered a manufacturing or materials defect.

This limited warranty will not reimburse you for the cost of any inconvenience, food, personal injury or property damage.

ITEMS MANUFACTURER WILL NOT PAY FOR:

1. Shipping cost, standard or expedited, for warranty and replacement parts

2. Service calls to your home.

3. Repairs when your product is used for other than normal, single-family household or residential use.

acts of God, improper installation or maintenance, installation not in accordance with electrical or plumbing codes, or use

of products not approved by the manufacturer.

5. Any food loss due to product failures or operating difficulties.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery of your product.

8. Repairs to parts or systems resulting from unauthorized modifications made to the product.

9. The removal and/or reinstallation of your product.

DISCLAIMER OF IMPLIED WARRANTIES and LIMITATION OF REMEDIES

Repair or replacement of defective parts is your exclusive remedy under the terms of this limited warranty. In the event of parts availability issues,

Manufacturer will not be responsible for any consequential or incidental damages arising from the breach of either this limited warranty or any

applicable implied warranty, or for failure or damage resulting from acts of God, improper care and maintenance, grease fire, accident, alteration,

replacement of parts by anyone other than Manufacturer, misuse, transportation, commercial use, abuse, hostile environments (inclement weather,

acts of nature, animal tampering), improper installation or installation not in accordance with local codes or printed manufacturer instructions.

THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY GIVEN BY THE MANUFACTURER. NO PRODUCT PERFORMANCE

SPECIFICATION OR DESCRIPTION WHEREVER APPEARING IS WARRANTED BY MANUFACTURER EXCEPT TO THE EXTENT SET

FORTH IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTY PROTECTION ARISING UNDER THE LAWS OF ANY STATE,

INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, IS HEREBY

LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY.

Neither dealers nor the retail establishment selling this product has any authority to make any additional warranties or to promise remedies

in addition to or inconsistent with those stated above. Manufacturer's maximum liability, in any event, shall not exceed the purchase price of the

product paid by the original consumer.

NOTE: Some states do not allow an exclusion or limitation of incidental or consequential damages, so some of the above limitations or exclusions

may not apply to you. This limited warranty gives you specific legal rights as set foth herein. You may also have other rights which vary from state

to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this product or

the Manufacturer will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer-purchaser

prior to discovery of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment selling this

product in order to obtain performance under this limited warranty.

If you wish to obtain performance of any obligation under this limited warranty, you should

write to:

Consumer Relations

P. O. Box 1240

Columbus, GA 31902-1240

Consumer returns will not be accepted unless a valid Return Authorization is first acquired. Authorized returns are clearly marked on the outside of

the package with an RA number and the package is shipped freight/postage pre-paid. Consumer returns that do not meet these standards will be

refused.

LIMITED WARRANTY

4. Damage, failures, or operating difficulties resulting from accident, alteration, careless handling, misuse, abuse, fire, flood,

the manufacturer reserves the right to substitute like or similar parts that are equally functional.

SCOPE OF COVERAGE PERIOD OF COVERAGE TYPE OF FAILURE COVERAGE

PERFORATION, MANUFACTURING,

AND MATERIAL DEFECTS ONLY

Stainless Burner

1 year from date of purchase*

Firebox, Lid, Cooking Grate and Emitters

All Other Parts

3 years from date of purchase*

10 years from date of purchase*

NOTE: DO NOT over tighten screws and washers that come into contact with porcelain coated surfaces. Over tightening may cause the porcelain coating to crack and break, resulting in

exposed metal that will be prone to rust.

REMARQUE: NE serrez PAS excessivement les vis et les rondelles qui sont en contact avec les surfaces au revêtement en porcelaine. Un serrage excessif peut fissurer ou briser le

revêtement en porcelaine, entraînant l'exposition du métal qui pourrait rouiller.

Nota: NO apriete demasiado los tornillos y arandelas que entren en contacto con las superficies revestidas de porcelana. Si los aprieta demasiado, se puede quebrar y romper el

revestimiento de porcelana lo que dejará expuesto el metal al proceso de oxidación.

ASSEMBLY/ ASSEMBLAGE/ ARMADO

Note: Orient panels as shown.

Remarque : orientez les panneaux

dans la direction indiquée.

Nota: Oriente los paneles como se

muestra.

#34

#25

#29

#31

#27

#28

#36

1ST

2ND

#44

#43

#48

#44

1ST

#16

#15

#17

Note: Retain tie wrap for bundling wires in later step.

Remarque: Conservez les attaches de brûleur latéral valve tuyau pour la mise en faisceau

des câbles lors d'une étape ultérieure.

Nota: Conservar cierre de lazo de la manguera de la válvula del quemador lateral para atar

cables en el paso posterior.

THIS SIDE UP

CE CÔTÉ VERS LE HAUT

ESTE LADO HACIA ARRIBA

Note: Untie match light chain and

hang inside cart for future use.

Remarque : détachez la chaîne

de l'allumette et suspendez-la

dans le chariot pour utilisation

future.

Nota: Desamarre la cadena del

palillo de encendido y cuélguela

dentro del carrito para usarlo en

el futuro.

#53

#37

1ST

2ND

#53

3RD

#53

#29

CAUTION

Failure to install grease tray will cause

hot grease to drip from bottom of grill

with risk of fire or property damage.

ATTENTION

Si le plateau d'écoulement de la graisse

n'est pas installé, de la graisse chaude

pourrait s'écouler de la partie inférieure

du gril et provoquer un risque d'incendie

ou des dommages matériels.

ADVERTENCIA

Si no instala la bandeja para la grasa

goteará grasa caliente desde el fondo de

la parrilla, lo que puede ocasionar el

riesgo de incendio o de daños materiales.

CAUTION

Avoid contact with hose when installing

heat shield.

ATTENTION

Évitez tout contact avec le tuyau lors de

l'installation de l'écran thermique.

ADVERTENCIA

Evite el contacto con la manguera cuando

instale el protector de calor.

#52

#53

#52

#38

#33

#10

#44

#10

#43

DANGER

Burner must properly engage valve as shown.

Failure to engage valve as shown may result in

personal injury and/or property damage.

Le brûleur doit être complètement inséré dans le

robinet, de la façon illustrée. Tout manquement à

l'insérer de la façon illustrée peut entraîner des

blessures ou des dommages matériels.

DANGER

PELIGRO

El quemador debe engancharse correctamente a la

válvula como se muestra. Si no se engancha a la

válvula como se muestra, podrían producirse

lesiones personales y/o daños a la propiedad.

1ST

#12

2ND

1ST

Before

Avant

Antes

After

Après

Después

WARNING

Flame carry over tube must be installed as shown.

Failure to install as shown may result in personal

injury and/or property damage.

Le tube de renvoi de flamme doit être installé de la

façon illustrée. Tout manquement à l'installer de la

façon illustrée peut entraîner des blessures ou des

dommages matériels.

AVERTISSEMENT

El tubo de arrastre de la llama debe instalarse como

se muestra. Si no lo instala como se muestra,

podrían producirse lesiones personales y/o daños a

la propiedad.

ADVERTENCIA

#14

#21

#24

IMPORTANT: Infrared emitters must be placed keeping both flat walls overlapped to prevent any flare-up.

IMPORTANT : Les émetteurs infrarouges doivent être placés de manière que les deux parois plates se

chevauchent pour fournir une protection contre les flambées soudaines.

IMPORTANTE: los emisores infrarrojos deben colocarse de tal forma que se empalmen las dos superficies

planas para prevenir llamaradas.

#22

#10

#23

#24

#22

2ND

#17

1ST

Remove screws and washers

Enlevez les vis et rondelles

Retire los tornillos y arandelas

Secure using screws that were removed from sideburner valve bracket

Fixez le tout au moyen des vis enlevées du support de valve du brûleur latéral

Fíjelo con los tornillos que retiró del soporte de la válvula del quemador lateral

#49

1ST

2ND

3RD

#51

#54

#56

#57

#55

Tie wrap

Attache

Cordón de

amarre

#51

1ST

2ND

Note: Use previously removed tie wrap(s) to bundle electrode

wires. Do not loop electrode wires when bundling.

Remarque : Utilisez les attaches enlevées précédemment pour

la mise en faisceau des fils d'électrode. N'enroulez pas les fils

d'électrode lors de la mise en faisceau.

Nota: Use la(s) correa(s) de amarre previamente retiradas para

amarrar juntos los alambres del electrodo. Evite los bucles en

los alambres del electrodo cuando los amarre juntos.

1ST

2ND

#40

#41

#42

#39

#40

OPRIMA

APPUYEZ

PRESS

Inspect your infrared grate before each use to ensure

that the openings are not covered with debris. See the

Grilling Guide for detailed cleaning instructions.

Inspectez votre grille infrarouge avant chaque

utilisation pour vous assurer que les orifices ne sont

pas recouverts de débris. Reportez-vous au guide des

grillades pour connaître les consignes de nettoyage

détaillées

Revise su parrilla infrarroja antes de cada uso para

asegurarse que las aberturas no están cubiertas de

escombros. Consulte la Guía de Asado a la Parilla

para la limpieza detallada.

Le robinet du réservoir doit être orienté vers le devant du

chariot une fois le réservoir ﬁxé en position. Une

mauvaise installation du reservoir pourrait endommager

le tuyau à gaz, créant un risque d'incendie.

ATTENTION

CAUTION

Cylinder valve must face to front of cart once tank is

attached. Failure to install cylinder correctly may allow

gas hose to be damaged in operation, resulting in the

risk of fire.

Una vez que el tanque haya quedado instalado, la válvula

del tanque debe quedar orientada hacia la parte

delantera del carrito. Si no se instala correctamente el

tanque, se puede dañar la manguera de gas durante el

suministro, lo que puede ocasionar el riesgo de incendio.

ADVERTENCIA

1ST

2ND

LP Cylinder

(not included)

Réservoir de gaz

(non compris)

Tanque de gas

(no viene incluido)

#26

EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.

Emergencies

Problem

Gas leaking from

cracked/cut/burned hose.

Gas leaking from LP cylinder.

Gas leaking from LP

cylinder valve.

Gas leaking between LP

cylinder and regulator

connection.

Fire coming through control

panel.

Grease fire or continuous

excessive flames above

cooking surface.

Burner(s) will not light

using ignitor.

(See Electronic Ignition

Troubleshooting also)

Continued on next page.

Possible Cause

• Damaged hose.

• Mechanical failure due to rusting or mishandling.

• Failure of cylinder valve from mishandling or

mechanical failure.

• Fire in burner tube section of burner due to blockage.

• Too much grease buildup in burner area.

GAS ISSUES:

• Trying to light wrong burner.

• Burner not engaged with control valve.

• Obstruction in burner.

• No gas flow.

• Coupling nut and LP cylinder valve not fully

connected.

ELECTRICAL ISSUES:

• Electrode cracked or broken; “sparks at crack.”

• Electrode tip not in proper position.

(Does not apply to SUREFIRE.)

• Wire and/or electrode covered with cooking residue.

• Wires are loose or disconnected.

• Wires are shorting (sparking) between ignitor and

electrode.

• Dead battery.

Prevention/Solution

• Replace LP cylinder.

• Turn off LP cylinder valve. Return LP cylinder to gas supplier.

• Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die

down. After fire is out and grill is cold, remove burner and inspect for spider nests or

rust. See Natural Hazard and Cleaning the Burner Assembly pages.

• Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die

down. After cooling, clean food particles and excess grease from inside firebox area,

grease tray, and other surfaces.

• See instructions on control panel and in Use and Care section.

• Make sure valves are positioned inside of burner tubes.

• Ensure burner tubes are not obstructed with spider webs or other matter. See

cleaning section of Use and Care.

• Make sure LP cylinder is not empty. If LP cylinder is not empty, refer to

“Sudden drop in gas flow.”

• Turn the coupling nut approximately one-half to three-quarters additional turn until

solid stop. Tighten by hand only - do not use tools.

• Replace electrode(s).

Main Burners:

• Tip of electrode should be pointing toward gas port opening on burner. The

distance should be 1/8” to 1/4”. Adjust if necessary.

Sideburner:

• Tip of electrode should be pointing toward gas port opening on burner. the

distance should be 1/8” to 3/16”. Adjust if necessary.

• Clean wire and/or electrode with rubbing alcohol and clean swab.

• Reconnect wires or replace electrode/wire assembly.

• Replace ignitor wire/electrode assembly.

• Replace with a new alkaline battery.

Troubleshooting

Burner(s) will not match light.

ELECTRONIC IGNITION:

• No spark, no ignition noise.

• No spark, some ignition noise.

• Sparks, but not at electrode or at full strength.

• See “GAS ISSUES:” .

• Match will not reach.

• Improper method of match-lighting.

• See Section I of Electronic Ignition System.

• See Section II of Electronic Ignition System.

• See Section III of Electronic Ignition System.

• Use long-stem match (fireplace match).

• See “Match-Lighting” section of Use and Care.

•Turn off gas at LP cylinder or at source on natural gas systems. Discontinue use of

product and replace valve/hose/regulator. Once valve/hose/regulator replaced

conduct complete leak check per manual.

• Improper installation, connection not tight, and/or

failure of rubber seal in clyinder valve.

•Turn off LP cylinder valve. Remove regulator from cylinder and visually inspect rubber

seal in cylinder valve for damage. If damage or cannot correct leak replace cylinder.

See LP Cylinder Leak Test and Connecting Regulator to the LP Cylinder.

Troubleshooting (continued)

Problem

Sudden drop in gas flow or

low flame.

Flames blow out.

Flare-up.

Persistent grease fire.

Flashback (fire in

burner tube(s)).

One burner does not light

from other burner(s).

Possible Cause

• Out of gas.

• Excess flow valve tripped.

• Vapor lock at coupling nut/LP cylinder connection.

• High or gusting winds.

• Low on LP gas.

• Excess flow valve tripped.

• Grease buildup.

• Excessive fat in meat.

• Excessive cooking temperature.

• Grease trapped by food buildup around

burner system.

• Burner and/or burner tubes are blocked.

• Grease buildup or food particles in end(s) of

carryover tube(s).

Prevention/Solution

• Check for gas in LP cylinder.

• Turn off knobs, wait 30 seconds and light grill. If flames are still low, turn off knobs

and LP cylinder valve. Disconnect regulator. Reconnect regulator and leak-test. Turn

on LP cylinder valve, wait 30 seconds and then light grill.

• Turn off knobs and LP cylinder valve. Disconnect coupling nut from cylinder.

Reconnect and retry.

• Refill LP cylinder.

• Refer to “Sudden drop in gas flow” above.

• Clean burners and inside of grill/firebox.

• Trim fat from meat before grilling.

• Adjust (lower) temperature accordingly.

• Turn knobs to OFF. Turn gas off at LP cylinder. Leave lid in position and let fire

burn out. After grill cools, remove and clean all parts.

• Turn knobs to OFF. Clean burner and/or burner tubes. See burner cleaning

section of Use and Care.

• Clean carry-over tube(s) with wire brush.

Troubleshooting - Electronic Ignition

Problem (Ignition)

SECTION I

No sparks appear at any

electrodes when Electronic

Ignition Button is pressed;

no noise can be heard from

spark module.

SECTION II

SECTION III

Sparks are present but not at

all electrodes and/or not at

full strength

Possible Cause

• Battery not installed properly.

• Dead battery.

• Button assembly not

installed properly.

• Faulty spark module.

• Output lead connections not

connected.

• Output lead connections not

connected.

• Arcing to grill away from

burner(s).

• Weak battery.

• Electrodes are wet.

• Electrodes cracked or broken

“sparks at crack”.

Check Procedure

• Check battery orientation.

• Has battery been used previously?

• Check to insure threads are properly

engaged. Button should travel up and

down without binding.

• If no sparks are generated with new

battery and good wire connections,

module is faulty.

• Are output connections on and tight?

• If possible, observe grill in dark

location. Operate ignition system and

look for arcing between output wires

and grill frame.

• All sparks present but weak or at

slow rate.

• Has moisture accumulated on electrode

and/or in burner ports?

• Inspect electrodes for cracks.

Prevention/Solution

• Install battery (make sure that “+” and “–” connectors are

oriented correctly, with “+” on cap end.)

• Replace battery with new alkaline battery.

• Unscrew button cap assembly and reinstall, making sure

threads are aligned and engaged fully.

• Replace spark module assembly.

• Remove and reconnect all output connections at module and

electrodes.

• Remove and reconnect all output connections at module and

electrodes.

• If sparks are observed other than from burner(s), wire insulation

may be damaged. Replace wires.

• Replace battery with a new alkaline battery.

• Use paper towel to remove moisture.

• Replace cracked or broken electrodes.

No sparks appear at any

electrodes when Electronic

Ignition Button is pressed;

noise can be heard from spark

module.

•Turn front of grill to face wind or increase flame height by turning gas valve to a

higher postion.

PARTS DIAGRAM/ SCHÉMA DES PIÈCES / VISTA ESQUEMÁTICA DE PIEZAS

#46

#20

#14

#21

#22

#23

#24

#12

#13

#52

#18

#19

#10

#15

#36

#43

#35

#55

#56

#57

#38

#33

#29

#41

#39

#28

#25

#27

#40

#41

#26

#31

#30

#34

#53

#37

#49 #50

#48

#45

#54

#47

#44

#11

#16

#32

#51

#42

#17

#58

NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from

those on your particular grill model. However, the method of assembly remains the same.

PARTS LIST

Key Qty Description

1 1 TOP LID

2 1 TEMPERATURE GAUGE

3 1 BEZEL, F/ TEMP GAUGE

4 1 LOGO PLATE

5 1 HANDLE F/ TOP LID

6 2 BEZEL, F/ HANDLE

7 2 RUBBER BUMPER, W/ HOLE, F/ TOP LID

8 2 RUBBER BUMPER, ROUND

9 1 TOP LID HARDWARE

10 1 FIREBOX

11 3 BURNER BRACE

12 3 MAIN BURNER TUBE, NO ELECTRODE

13 3

ELECTRODE SET, F/ MAIN BURNER,

500MM WIRE

14 2 FLAME CARRY OVER TUBE

15 1 MAIN CONTROL PANEL, TOP

16 1 MAIN CONTROL PANEL, BOTTOM

17 1 HOSE VALVE REGULATOR

18 4 CONTROL KNOB

19 4 BEZEL, KNOB

20 1 IGNITER SWITCH MODULE

21 3 HEAT TENT

22 1 WARMING RACK

23 3 COOKING GRATE

24 3 COOKING GRATE, INFRARED EMITTER

25 1 BOTTOM SHELF

26 1 TANK THUMBSCREW

27 2 CASTER, LOCKING

28 2 CASTER, FIXED

29 1 LEFT CART ASSEMBLY

30 1 MATCH HOLDER

31 1 RIGHT CART ASSEMBLY

32 1 GROMMET

33 2 REAR CART PANEL

34 1 UPPER REAR CART PANEL

35 1 FRONT DOOR BRACE

36 4 SIDE SHELF CONNECTION BRACE

37 2 RAIL, F/ GREASE TRAY

38 1 GREASE TRAY

39 1 LEFT DOOR, NO HANDLE

Key Qty Description

40 1 RIGHT DOOR, NO HANDLE

41 2 HANDLE, F/ DOOR

42 4 DOOR BUSHING, F/ HANDLE

43 1 LEFT SIDE SHELF

44 1 SIDEBURNER SHELF

45 1 DRIP PAN, F/ SIDEBURNER

46 2 SILICONE RUBBER BUMPER, F/ SIDEBURNER

47 1 SIDEBURNER LID

48 1 CONTROL PANEL, F/ SIDEBURNER SHELF

49 1 SIDEBURNER

50 1 ELECTRODE, F/ SIDEBURNER

51 1 WIRE, F/ SB ELECTRODE

52 1 HEAT SHIELD, FIREBOX

53 1 HEAT SHIELD, F/ TANK

54 1 GRATE, F/ SB

55 1 ELECTRONIC IGNITION MODULE

56 1 CAP, F/ EI MODULE

57 1 HEAT SHIELD, F/ IGNITION MODULE

58 1 HOSE/ REGULATOR REPLACEMENT ONLY

NOT Pictured

… 2 MAGNET

… 1 PRODUCT MANUAL, ENGLISH, FRENCH, SPANISH

… 1 HARDWARE PACK

… 1 IR CLEANING TOOL

HARDWARE LIST/ LISTA DE HERRAJES/ LISTE DES FERRURES

Key/ Réf./ Clave

Description/ Description/ Descripción

Picture/ Illustré/ Ilustra

Qty/ Qté/ Cant

1/4-20x2-3/8" Screw

Vis ¼-20× po2-3/8

Tornillo de 1/4 -20 x 2-3/8"

1/4-20x1-1/2" Screw

Vis ¼-20×1½ po

Tornillo de 1/4 -20 x 1-1/2"

1/4-20x1/2" Screw

Vis ¼-20×½ po

Tornillo de 1/4 -20 x 1/2"

#8x3/8" Sheet Metal Screw

Vis à tôle nº 8×3/8 po

Tornillo para metale No. 8 de 3/8''

#10-24x3/8" Screw

Vis nº 10-24×3/8 po

Tornillo No. 10-24 de 3/8"

1/4 Nut

Écrou de ¼

Tuerca de 1/4

Battery AA

Pile AA

Batería AA

Cleaning tool

Nettoyage de l'instrument

Herramienta de limpieza para el emisor IR

#10-24x3/4" Screw

Vis nº 10-24×3/4 po

Tornillo No. 10-24 de 3/4"

Wing Nut

Écrou à oreilles

Tuerca de mariposa

#8-32x3/8" Screw

Vis nº 8-32×3/8 po

Tornillo No. 8-32 de 3/8"

Control knob

Bouton de réglage

Perilla de control

Bezel f/ control knob

Collerette d'encastrement du bouton de réglage

Marco, perilla de control